The pump type VBR (VS6) is a double casing single or multistage design incorporating single or multi radial vane impellers with front and rear wear rings, each impeller has its own diffuser. VBR vertical shaft pumps feature a barrel (suction can) and are suitable for dry or wet well uses. This range is also available without the barrel please see our VIR (VS1) pump type. The design complies with the latest edition of the American Petroleum Institute standard 'Centrifugal Pumps For General Refinery Services', also known as API 610/ ISO13709.
For alternative specifications contact us.
casing (discharge head):
The suction and discharge nozzles are located on the discharge head. Nozzle flanges are as per the ASME standards. Optional casings can also be provide which are designed for maximum allowable working pressure of class 600 # or 900 # and the discharge head is designed to withstand 2 or 4 times nozzle loads as specified in API. Steam tracing/insulation to the casing, when high temperature application. Discharge head in forging on customer request.
Bottom casing (bell mouth) is provided which ensure smooth flow of the liquid inside the pump thereby ensuring no cavitation’s. Specially designed self lubricated bearing is provided in the bell mouth to ensure added shaft rigidity
Inner casing (bowl assembly):
The bowl houses a separately cast diffuser or guide ring or both cast in one piece. These bowls are bolted together individually which permits easy disassembly. Bowls are held together with bolts and with a Metal-to metal joint which ensure leak-proof operation and can be used in high temperature application
The pumps are provided with suction cans which is a substitute for the vessel and form the sump from which liquid can be pumped to the desired output. These cans are manufactured complying the Boiler and pressure vessel standards. On customer request these cans can be provided with U-Stamping.
Nozzle orientation arrangement
Suction & discharge nozzles are in side-side orientation and can be provided in 300 & 600 class flange rating as per ANSI B 16.5. Flanges of suction & discharge nozzles are raised faced with a serrated finish.
Drain connection is provided with a ½” ANSI flange on sizes till 4’’ and ¾’’ on sizes 5’’ and higher. All provided connections are shipped with plugs made of materials compatible with the casings, unless otherwise specified. Vent connection is provided at the highest point in the seal recirculation piping. Additional connections can be provided for Quenching, Cooling water inlet & outlet & Warming line when specified. An equalizing line connection is provided for returning excessive gas from the vessel or the suction can which can be connected to the clients vent system.
Sr. No. List of Auxiliary Connections List of drain connection sizes
An 18-8 stainless steel spiral wound gasket with non-Asbestos filter is provided
The stuffing box is deep enough to accept various seal designs including tandem and double seals. Water cooled or steam heated stuffing box designs are available at extra cost when specified or required. The stuffing boxes are designed in such a manner so as to ensure min 30 % margin within the Box pressures and the vapour pressure values for satisfactory operation of the seals.
The impeller is an enclosed, single suction type and is keyed to the shaft. It is provided with both front and back wear rings. Optional Inducer design is also available for critical NPSH requirement or under critical suction conditions. Impellers are with close grain cast material and with finished hydraulic passages for better efficiencies.
Impeller wear rings
The impeller wear rings are held on impeller with an interference fit and secured in positions with set screws to ensure positive fitment.
Case wear rings
The case wear rings are inserted in the casing with a slight interference fit and secured in position with set screws.
Shaft and shaft sleeves
Shafts are provided in sizes so that it can transmit the required torque. Shaft length is decided considering certain design limits. Usually single shaft length is limited to 2 m. Shafts can be made available in all materials as per API standard. Mechanical seal sleeve is axially located with sleeve retainer at the outer end.
This range is also available without the barrel please see our VIR (VS1) pump type.